Lincoln Electric SVM165-A Manuel d'utilisateur télécharger pdf (Page 21)

Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC

Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC

B-9

OPERATION

POWER MIG 350MP

5. Rotate the spindle and adapter so the retaining

spring is at the 12 o'clock position.

6. Position the Readi-Reel so that it will rotate in a direc-

tion when feeding so as to be de-reeled from top the

of the coil.

7. Set one of the Readi-Reel inside cage wires on the

slot in the retaining spring tab.

8. Lower the Readi-Reel to depress the retaining spring

and align the other inside cage wires with the grooves

in the molded adapter.

9. Slide cage all the way onto the adapter until the

retaining spring "pops up" fully.

Check to be sure the retaining ring has fully returned to the locking

position and has securely locked the Readi-Reel cage in place.

Retaining spring must rest on the cage, not the welding electrode.

-----------------------------------------------------------------------------------------------

10. To remove Readi-Reel from Adapter, depress retain-

ing spring tab with thumb while pulling the Readi-

Reel cage from the molded adapter with both hands.

Do not remove adapter from spindle.

FIGURE B.4

TO MOUNT 10 to 44 Lb. (4.5-20 kg) SPOOLS (12"/300

mm Diameter) or 14Lb.(6 Kg) Innershield Coils:

(For 13-14 lb. (6 Kg) Innershield coils, a K435 Coil

Adapter must be used).

1. Open the Wire Drive Compartment Door

2. Depress the Release Bar on the Retaining Collar

and remove it from the spindle.

3. Place the spool on the spindle making certain the

spindle brake pin enters one of the holes in the

back side of the spool (Note: an arrow mark on the

spindle lines up with the brake holding pin to assist

in lining up a hole). Be certain the wire comes off

the reel in a direction so as to de-reel from the top

of the coil.

CAUTION

PROCEDURE FOR CHANGING

DRIVE AND IDLE ROLL SETS

1. Turn off the power source.

2. Release the pressure on the idle roll by swinging

the adjustable pressure arm down toward the back

of the machine. Lift the cast idle roll assembly and

allow it to sit in an upright position.

3. Remove the outside wire guide retaining plate by

loosening the two large knurled screws.

4. Twist the drive roll retaining mechanism to the

unlocked position as shown below and remove the

drive roll. (See Figure B.3)

5. Remove the inside wire guide plate.

6. Replace the drive and idle rolls and inside wire

guide with a set marked for the new wire size.

NOTE: Be sure that the gun liner and contact tip

are also sized to match the selected wire size.

7. Manually feed the wire from the wire reel, over the

drive roll groove and through the wire guide and

then into the brass bushing of the gun and cable

assembly.

8. Replace the outside wire guide retaining plate by

tightening the two large knurled screws. Reposition

the adjustable pressure arm to its original position

to apply pressure. Adjust pressure as necessary.

WIRE REEL LOADING - READI-REELS,

SPOOLS OR COILS

To Mount a 30 Lb. (14 kg) Readi-Reel Package

(Using the Molded Plastic K363-P Readi-Reel

Adapter):

. Open the Wire Drive Compartment Door

2. Depress the Release Bar on the Retaining Collar

and remove it from the spindle.

3. Place the Optional Adapter on the spindle

4. Re-install the Retaining Collar. Make sure that the

Release Bar “pops up” and that the collar retainers

fully engage the retaining ring groove on the spin-

dle.

LOCKED POSITION

UNLOCKED POSITION

FIGURE B.3

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 127 128

Commentaires sur ces manuels

Pas de commentaire

Lincoln Electric SVM165-A Manuel d'utilisateur Page 21

Commentaires sur ces manuels

Produits connexes et manuels pour Système de soudage Lincoln Electric SVM165-A